{"id":256,"date":"2024-04-24T21:20:09","date_gmt":"2024-04-24T12:20:09","guid":{"rendered":"http:\/\/selserver3.kir.jp\/www.shinkoh-elecs.jp\/?page_id=256"},"modified":"2024-10-28T13:11:35","modified_gmt":"2024-10-28T04:11:35","slug":"notice","status":"publish","type":"page","link":"https:\/\/www.shinkoh-elecs.jp\/en\/support\/notice\/","title":{"rendered":"Basic Information – Cautions of Use"},"content":{"rendered":"
\n
\n
\n

Notice<\/h3>\n<\/div>\n<\/div>\n<\/div>\n
\n

Load to Product<\/h4>\n
\n

Be aware that much load gives a damage to product as deforming or deterioration. At forming of terminals, fasten the root of terminals. Lead-cutting or insert\/remove of connector should be worked in room temperature.<\/p>\n<\/section>\n

Deterioration, scratch and grime<\/h4>\n
\n

To avoid tarnish, alteration and stain by the oxidation or corrosion, keep the product in environment of non-condensing, no water drop, and no corrosive gases or salt air. We recommend to use desiccator with nitrogen air. Please note the scratches, stains, or bruises on the products, especially on sensing surface, for storage and handling.<\/p>\n<\/section>\n

Vibration and Impact<\/h4>\n
\n

Please note Mechanical vibration and an impact by the preservation, carriage and use as it might occur some damages or transformation of product.<\/p>\n<\/section>\n

Ambient light<\/h4>\n
\n

Please use in environment where there is no direct ambient light. Light modulation type is available for solution with influence of ambient light.<\/p>\n<\/section>\n

Shielding object<\/h4>\n
\n

For light shielding, High extinction efficiency is recommended in material.<\/p>\n<\/section>\n

Cleaning <\/h4>\n
\n

Don’t use chemicals but blower or soft cloth for cleaning. If you have any problem, please consult our Sales Dept.<\/p>\n<\/section>\n

Static electricity<\/h4>\n
\n

The worker, working table, instrument and circuit should be always grounded to prevent damage of product from static electricity or surge voltage.<\/p>\n<\/section>\n

Notice of Soldering<\/h4>\n
\n

Please check the performance of soldering at customer’s assembly in advance. It also need to check the problem with the appearance or reliability by using of flux.<\/p>\n<\/section>\n

Compliance of ratings and notice<\/h4>\n
\n

Operation never exceeds each value of Maximum Ratings and comply with each notice at design\/ Operation. Please note that we are free from any risk, expense, and damage caused by ignorance and defects of these ratings and\/or notice directly and indirectly.<\/p>\n<\/section>\n

Disassembly of Product<\/h4>\n
\n

Don’t take the product apart for danger. After being disassembled without our formal approval in advance, we can’t warant any performance on specification sheet. Please ask our examinatin if it needs analysis.<\/p>\n<\/section>\n

Measure for UV safety<\/h4>\n
\n

Please do measure for UV safet – for example, UV protection lenses of spectacles – as it is danger for eyes to look UV light directly or by way of optical system during operation. Same measure is also required in possibility of reflection of UV light.<\/p>\n<\/section>\n

Fail safe \/ Fault tolerance<\/h4>\n
\n

A fail-safe describes a device, parts or system which, in the even of failure, fails in a way that will cause no harmor at least a minimum of harm to other device or danger to personnel. In the event of failure, for example, operating fuse for the safety can apply for this designing. Please plan the safety design for entire system and device, especially in applications which require reliability and safety about function and accuracy. Also, we recommend that the design based on “Fault Tolerant” should properly hold the system despite malfunctionor wrong operation. Please consider the redundancy design, especially in applications which require the faulttolerance.<\/p>\n<\/section>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

Notice Load to Product Be aware that much load gives a damage to product as deforming or deterioration. At forming of terminals, fasten the root of terminals. Lead-cutting or insert\/remove of connector should be worked in room temperature. Deterioration, scratch and grime To avoid tarnish, alteration and stain by the oxidation or corrosion, keep the […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":254,"menu_order":34,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_acf_changed":false,"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_locale":"en_US","_original_post":"http:\/\/selserver3.kir.jp\/www.shinkoh-elecs.jp\/?page_id=43","footnotes":""},"class_list":["post-256","page","type-page","status-publish","hentry","en-US"],"acf":[],"aioseo_notices":[],"_links":{"self":[{"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/pages\/256"}],"collection":[{"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/comments?post=256"}],"version-history":[{"count":8,"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/pages\/256\/revisions"}],"predecessor-version":[{"id":2883,"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/pages\/256\/revisions\/2883"}],"up":[{"embeddable":true,"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/pages\/254"}],"wp:attachment":[{"href":"https:\/\/www.shinkoh-elecs.jp\/wp-json\/wp\/v2\/media?parent=256"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}